McIntosh MC7106 6-Channel Configurable Power Amplifier

Free Shipping (Contiguous U.S. Only)

General:
The McIntosh MC7106 is an exceptionally flexible six-channel power amplifier designed for high-performance home theater, multi-channel, and multi-zone systems.

In its standard configuration it delivers 100 watts per channel into 8 ohms, or 160 watts per channel into 4 ohms, across all six channels.

Where things get especially interesting is its ability to bridge any of its three channel pairs.

Each bridged pair delivers 320 watts into 8 ohms, allowing the MC7106 to be configured for anywhere from three to six output channels depending on your system.

It also features McIntosh Power Guard protection, six front-panel LED power-level displays, and Lucasfilm THX Audio certification.

MC7106 Output Configurations:

6-Channel Mode:
6 x 100W into 8 ohms
6 x 160W into 4 ohms

5-Channel Mode:
4 x 100W/160W channels
1 x 320W bridged channel

4-Channel Mode:
2 x 100W/160W channels
2 x 320W bridged channels

3-Channel Mode:
3 x 320W bridged channels

Each 320W output is created by bridging a pair of amplifier channels.

Bridged operation is rated for 8-ohm loudspeaker loads only.

Condition:
This MC7106 is in very clean overall condition with minimal signs of use.

The six front-panel LED power-level displays are especially attractive in operation and feature an adjustable brightness control located on the rear panel.

Like most McIntosh components of this era, the front panel uses printed glass, providing a durable finish that keeps the lettering crisp and resistant to wear.

The amplifier has been fully tested in our lab and is performing properly.

Included are the original McIntosh box, owner's manual, and power cord.

Click below to add our recommended matching cables from Kimber Kable, all brand new as SkyFi is an official Kimber dealer.

Ascent Series Hero Analog Interconnects (PAIR) - RCA Ultraplate or WBT Connectors

Ascent Series Hero Analog Interconnects (PAIR) - BALANCED XLR Connectors

Kimber Kable - Speaker Cables

Kimber Kable - Bi-Wire Speaker Cables

Specifications

PERFORMANCE LIMITS
Performance limits are the maximum deviation from perfection permitted for a Mclntosh instrument. We promise you that when you purchase an MC7106 from a Mclntosh franchised dealer, it will be capable of performance at or better than these limits.

POWER OUTPUT, SIX CHANNELS
100 watts per channel into 8 ohm loads, or 160 watts per channel into 4 ohm loads minimum sine wave continuous average power output per channel, all channels operating.

The output RMS voltage is:
28.3V across 8 ohms
25.2V across 4 ohms

POWER OUTPUT, TWO CHANNELS BRIDGED
320 watts into an 8 ohm load, minimum sine wave continuous average power output.

The output RMS voltage is:
50.6V across 8 ohms

OUTPUT LOAD IMPEDANCE
8 or 4 ohms, for all six separate channels
8 ohms, Bridged operation

RATED POWER BAND
20Hz to 20,000Hz

TOTAL HARMONIC DISTORTION
0.005% maximum harmonic distortion at any power level from 250 mW to rated power output.

IHF DYNAMIC HEADROOM
8 ohms, 1.8dB
4 ohms, 2.1dB

FREQUENCY RESPONSE
+ 0, -0.25dB from 20Hz to 20,000Hz
+ 0, -3.0dB from 10Hz to 100,000Hz

INPUT SENSITIVITY
1V, (2.5V with Level control at center detent)

A-WEIGHTED SIGNAL-TO-NOISE RATIO
93dB (113dB below rated output)

INTERMODULATION DISTORTION, SMPTE
0.005% maximum if instantaneous peak power does not exceed twice the output power rating.

RATINGS
WIDE BAND DAMPING FACTOR
200 at 8 ohms
100 at 4 ohms

INPUT IMPEDANCE
20,000 ohms

POWER GUARD
Clipping is prevented and THD does not exceed 2% with up to 14dB overdrive at 1000Hz.

POWER REQUIREMENTS
120V, 50/60Hz, 12A UL/CSA

FRONT PANEL: Glass panel. Illuminated. Power Guard lights. Power LED's indicate when each channel pair is active.

BACK PANEL: Output terminals. Audio inputs and outputs. Power control jacks: in and out. Power sw: on or off/remote. THX 25 pin input connector. Level controls: bridged and stereo/mono. Mode sw: bridged, stereo or mono. Multi-room connector. Fuse.

Size 7-1/16"H, 17-1/2"W and 20"D. Weight 48 lb.

Click here for a PDF copy of the Original MC7106 Sales Brochure

Click here for a PDF copy of the MC7106 Owner's Manual

Click here to view all McIntosh pieces available for purchase on our website

The SkyFi Testing Process for Solid State Amplifiers:

We start with a visual inspection of all internal components to make sure that there are no signs of heat stress or damage. Capacitors are checked for telltale signs of predictive failure including bulging, shrunken wrappers, or physical leakage. We also inspect the PCBs for discoloration from resistors or transistors that may have been running hot. On vintage units we often spot check select capacitors for value and ESR.

If the amplifier passes visual inspection, we move on to a controlled power on sequence using a Sencore safety analyzer to monitor current draw in real time. Once the amplifier is determined to be safe to operate, we connect it to full AC mains for function and power testing. We connect the speaker outputs of the amplifier to a Sencore PA81 Power Analyzer which acts as a dummy load, DC offset monitor, and oscilloscope interface. We start with a low level 1KHz test signal at the amplifier’s input and slowly increase its amplitude while monitoring the output on an oscilloscope for signs of noise, clipping, distortion, or improper channel balance. We continue increasing the signal level until the amplifier reaches clipping. At this point we take an output power measurement and compare it to the spec sheet of the amplifier to verify proper performance. If the device under test has both balanced and single ended inputs they are both tested at this time. We finish off the bench evaluation with a 1KHz square wave check and a 20Hz to 20KHz sine sweep to assess the amplifier’s frequency response characteristics. This battery of tests will usually reveal if the amplifier has any issues that need further attention.

Before the device leaves the bench, we perform a listening test with actual music using a variety of preferred test tracks. Our benches are outfitted with familiar monitor speakers which help us identify inconsistencies that will not always show up on our test gear. The main things that we are listening for are hum or noise with no signal present, proper center image, clicks, pops, or any other obvious undesirable audio characteristics.

If the unit passes all of these tests it is moved to our long term testing rig where we simulate real word operating conditions for 6-8 hours. This allows us to monitor the unit for signs of thermal runaway or intermittent issues that only crop up when the unit has fully come up to temperature.