Skip to content

Cart

Audio Research SP-15 Flagship Hybrid Tube Preamplifier - Serviced

Sale price$7,490.00
Free Shipping (Contiguous U.S. Only)

Pickup available at SkyFi 479

Usually ready in 24 hours

Audio Research SP-15 Flagship Hybrid Tube Preamplifier - Serviced - Preamplifier

Audio Research SP-15 Flagship Hybrid Tube Preamplifier - Serviced

SkyFi 479

Pickup available, Usually ready in 24 hours

479 South Broad Street
Glen Rock NJ 07452
United States

+12018790000

General:
The Audio Research SP-15 was the flagship two-piece preamplifier introduced by Audio Research in 1988, representing the pinnacle of their engineering and circuitry at the time as the successor to the legendary SP-11.

Key features include a hybrid vacuum tube design utilizing three 6DJ8 (ECC88 / 6922) tubes housed in the main preamplifier board for the phono and intermediary gain stages, alongside a dual-chassis construction with a separate power supply that keeps sensitive, low-amplitude audio circuits safely away from transformer interference.

The stellar phono stage is a true standout, featuring convenient front-panel impedance adjustment that makes switching between Moving Magnet and Moving Coil cartridges easy, while the rear of the power supply includes switched AC outlets to easily integrate source components like CD players and tape decks.

During testing, we thoroughly enjoyed this SP-15 and found that it easily goes toe-to-toe with other two-piece preamplifiers from its era and even newer designs.

Best of all, for peace of mind regarding performance and reliablity, this unit was fully serviced in-house, addressing key areas to ensure the long-term stability that is especially critical for vintage Audio Research gear.

Included in the sale are the preamplifier chassis, the dedicated power supply chassis, the umbilical power linking cable, and a standard IEC power cable.

SkyFi Cosmetic Notes:
Light wear is present on the back sides of the faceplates. Two of the knobs on the preamp chassis have blemishes. Overall condition is excellent.

SkyFi Technical Notes:
This SP-15 arrived in non working condition. ARC had previously repaired the unit in May of 2019, replacing a failing FET in the phono section and recapping the power supply. After a period of trouble free operation the unit failed once again. In house service here at SkyFi involved rebuilding the (2 of 4) local voltage regulators in the preamp chassis along with the replacement of (3) FETs in non-inverting preamp section on the L channel. We also repaired the muting circuit, swapping out a faulty 555 timer and replacing the muting relays in the non-inverting section of the preamp. It now works great and will come with a one year SkyFi Warranty.  


Brand Background:
Audio Research continues its dedication to unparalleled musical expression and crafting components of the highest quality and lasting value for its customers. Our long-term dedication to service is peerless in this industry (Audio Research, with few exceptions, can repair anything ever produced during its entire history). We continue to seek out new and exciting ways to make music more real and more enjoyable. More than just a name or a marketing tool, Audio Research has come to represent exceptional performance and long-term value. Experience Audio Research – experience High Definition®.

Ownership:
Second Owner

Connections:
RCA inputs/outputs, XLR outputs, IEC power input, Ground Terminal,

General Sound:
Smooth, uncolored, undistorted natural and clean

Cosmetic Condition:
7/10 = Good. One or two minor scratches. Well Maintained. See our detailed rating description here.

Working Condition:
Working perfectly and tested in our lab and listening room.

Included:
Unit, Power supply, Power Cord,

Packing:
Will be packed using our highly developed in-house process and custom packing materials.Original MSRP:
$5,998.00

Specs:
Frequency response
High level input: ±1dB 0.2Hz to 100kHz. -3dB below 0.1Hz and above 200kHz. Phono input: ±.2dB of RIAA 20Hz to 40kHz. ±1dB of RIAA 1.0Hz to 100kHz.
Distortion (THD)
Harmonic distortion: Less than .005% at 2V RMS output, 5Hz to 20kHz (Typically less than .001% at midband, phono or line input). Intermodulation distortion: Less than .003% at 2V RMS output
Noise & hum
IHF weighted, shorted input: Output (Gain down): 6µV (110dB below rated output). Input (High level): 3µV equivalent input (110dB below 1V input). Phono: 0.15µV equivalent input (76dB below 1mV input)
Gain
At 1kHz, bypass mode: Phono input to tape output: 46dB (0.2V output from 1mV input). Phono input to main output: 75dB (0.175mV input for 1V output). High level input to main output: 29dB (36mV input for 1V output).
Input impedance
Phono: Front panel selectable 47K, 100, 30, 10, 3 ohms. Phono input capacitance: 150 pF at 10kHz. High level: 20K ohms or higher, depending on switch functions.
Output impedance
200 ohms main, direct, inverted outputs. 500 ohms tape output. Recommended load 60K-100K ohms and 100pF (20Kohms minimum, 1000pF maximum)
Output polarity
Tape outputs, direct output: Non-inverting. Invert output: Inverting. Main outputs (2): Selectable non-inverting or inverting. All outputs may be used simultaneously.
Maximum inputs
Phono: 350 mV RMS at 1kHz, 1200 mV RMS at 10kHz (0.1 second maximum duration, 6dB less if continuous). High level: 25V RMS.
Rated outputs
2V RMS 1Hz to 100kHz main, direct, inverted outputs. (Maximum 80V RMS at 0.2% THD at 1kHz into 60K ohm load with 2.85V RMS high level input).
Power supplies
\-
Tube complement
(3) 6DJ8/ECC88
Power requirements
95-135VAC 60Hz, 190-270VAC 50/60Hz, 130 Watts maximum
Other
Filter: 25Hz Hi-pass phono subsonic 6dB/octave rolloff (to eliminate ringing) with transition to 12dB/octave at 10Hz. Front panel switchable phono only. Controls (6): Gain, Attenuator, Balance, Mode, Input, Impedance. Switches (8): Tape monitor, Copy, Tape 1/2, Tape 1to2 / 2to1, Mute, Invert phase, Bypass, Filter.

Dimensions:
19" W x 5.25" H x 10.25" D (each chassis)

Weight:
45 lbs.

Approximate Age:
1988

Link to Manual:
Click Here

Recommended Cables:
Kimber Kable - RCA Interconnects - Better

Kimber Kable - RCA Interconnects - Best

Kimber Kable - Phono Interconnects

Kimber Kable - BALANCED XLR Connectors - Better

Kimber Kable - BALANCED XLR Connectors - Best

Kimber Kable - Power Cords - Better

Kimber Kable - Power Cords - Best

Testing Process:
We start with a visual inspection of all internal components to make sure that there are no signs of heat stress or damage. Capacitors are checked for telltale signs of predictive failure including bulging, shrunken wrappers, or physical leakage. We also inspect the PCBs for discoloration from resistors or transistors that may have been running hot. On vintage units we often spot check select capacitors for value and ESR.

When we first power on a preamplifier we connect its RCA output to a Sencore PA81 Power Analyzer which simulates real world loading conditions and gives us an oscilloscope interface.

The first order of business is checking that the volume control works smoothly throughout its entire range with acceptable channel balance. This is accomplished by feeding a 1 KHz sine wave into one of the preamp’s line level inputs while monitoring the preamp’s output on an oscilloscope.

We then switch to a 1 KHz square wave to test the tone controls, loudness function, and filters where applicable. During this step we are watching for equal alteration of the test signal by both channels. This also helps us identify dirty controls that will need treatment.

Once the basic line stage functions are verified, we test each input individually. This is especially important for devices that use relays to select their sources. If the preamp is equipped with a phono stage we test that as well. We use an inverse RIAA filter which allows us to feed a reference test signal into the phono input with the proper RIAA equalization and level. A square wave or sine sweep is used to verify that the device’s phono stage is faithfully reproducing the RIAA curve. If the preamp under test has balanced inputs and/or outputs these are tested as well.

We finish up our bench testing with a listening test with our bench amplifier and reference speakers. During this test we check for hum or hiss that may not have shown up in earlier testing. We also check that all of the tone controls and filters perform as expected.

If the preamplifier has remote control functions these are also tested. Preamps with tube circuits or complicated power supply topologies are connected at our long term test rig for extended stress testing under real world conditions.

SKU: 108133
Audio Research SP-15 Flagship Hybrid Tube Preamplifier - Serviced - Preamplifier
Audio Research SP-15 Flagship Hybrid Tube Preamplifier - Serviced Sale price$7,490.00