Skip to content

Cart

Your cart is empty

NEW ARRIVALS + SYSTEM OF THE WEEK NEWSLETTER

Subscribe to receive updates, access to exclusive deals, and more... We promise not to give your info away.

NAD C 326BEE Integrated Amplifier with Remote

Sale price$0.00
Free Shipping on *ALL* Electronics (Excluding Speakers, Contiguous 48 US States Only)

Pickup currently unavailable at SkyFi 479

Nad C 326Bee Integrated Amplifier With Remote

NAD C 326BEE Integrated Amplifier with Remote

SkyFi 479

Pickup currently unavailable

479 South Broad Street
Glen Rock NJ 07452
United States

+12018790000

Well regarded and super clean Integrated from NAD.

Capable of 50WPC which is enough to drive most speakers to a nice level. Also Includes the remote and original box.

More from NAD:

Tracing its lineage back to the original NAD 3020, an amplifier that changed the industry, the C 326BEE is a truly extraordinary component.

With more than twice the power output, as well as a pure Class A preamp circuit, the C 326BEE delivers an outstanding performance.

Featuring 7 line inputs, and a pre-amplifier section that can be separated from the power amplifier for easy upgrades, the C 326BEE is a product that cannot be ignored.

The C 326BEE also benefits mightily from NAD’s PowerDrive™ circuit topology, which allows the C 326BEE to deliver maximum performance to even the most powerful of speakers.

With significantly low levels of both noise and distortion, the C 326BEE is a dream product for any hi-fi system, and will deliver a captivating and amazing listening experience unlike anything you’ve heard before.

Link to Review:

https://www.theabsolutesound.com/articles/nad-c326bee-integrated-amplifier-and-c545bee-cd-player-tas-199/

Recommended Cables:

Kimber Kable - RCA Interconnects - Better

Kimber Kable - RCA Interconnects - Best

Kimber Kable - Speaker Cables - Better

Kimber Summit Series Monocle XL Speaker Cables (PAIR) - Best

Kimber Summit Series BiFocal XL Bi-Wire Speaker Cables (PAIR) - Best If Applicable 

Kimber Kable - Power Cords - Better

Kimber Kable - Power Cords - Best

The SkyFi Testing Process for Solid State Amplifiers:

We start with a visual inspection of all internal components to make sure that there are no signs of heat stress or damage. Capacitors are checked for telltale signs of predictive failure including bulging, shrunken wrappers, or physical leakage. We also inspect the PCBs for discoloration from resistors or transistors that may have been running hot. On vintage units we often spot check select capacitors for value and ESR.

If the amplifier passes visual inspection, we move on to a controlled power on sequence using a Sencore safety analyzer to monitor current draw in real time. Once the amplifier is determined to be safe to operate, we connect it to full AC mains for function and power testing. We connect the speaker outputs of the amplifier to a Sencore PA81 Power Analyzer which acts as a dummy load, DC offset monitor, and oscilloscope interface. We start with a low level 1KHz test signal at the amplifier’s input and slowly increase its amplitude while monitoring the output on an oscilloscope for signs of noise, clipping, distortion, or improper channel balance. We continue increasing the signal level until the amplifier reaches clipping. At this point we take an output power measurement and compare it to the spec sheet of the amplifier to verify proper performance. If the device under test has both balanced and single ended inputs they are both tested at this time. We finish off the bench evaluation with a 1KHz square wave check and a 20Hz to 20KHz sine sweep to assess the amplifier’s frequency response characteristics. This battery of tests will usually reveal if the amplifier has any issues that need further attention.

Before the device leaves the bench, we perform a listening test with actual music using a variety of preferred test tracks. Our benches are outfitted with familiar monitor speakers which help us identify inconsistencies that will not always show up on our test gear. The main things that we are listening for are hum or noise with no signal present, proper center image, clicks, pops, or any other obvious undesirable audio characteristics.

If the unit passes all of these tests it is moved to our long term testing rig where we simulate real word operating conditions for 6-8 hours. This allows us to monitor the unit for signs of thermal runaway or intermittent issues that only crop up when the unit has fully come up to temperature.

Specifications:

Output power: 50WPC, 20 – 20kHz, 0.009% THD, into 4 or 8 ohms

Dimensions: 17-1/8″ W x 4″ H x 14-1/4″ D

Weight: 15.2 lbs.

Link to Manual:

https://nadelectronics.com/wp-content/uploads/2016/09/C-326BEE-Stereo-Integrated-Amplifier-English-Manual.pdf

Item

Included

Original Box

Yes Included

Manual

Not Included

Remote

Yes Included

Cables

Yes - Power Only

Physical Condition (Info Here)

8 / 10

Working Condition

10 / 10

SKU: 104203